Login or Register for FREE!
Subelement G6
Circuit Components
Section G6A
Resistors; capacitors; inductors; rectifiers; solid-state diodes and transistors; vacuum tubes; batteries
What is the minimum allowable discharge voltage for maximum life of a standard 12 volt lead-acid battery?
  • 6 volts
  • 8.5 volts
  • Correct Answer
    10.5 volts
  • 12 volts

\(10.5\) volts is the minimum allowable discharge voltage for a standard 12 volt lead acid battery to retain maximum cell life.


Discharging below this level can cause changes in the chemical nature of the cell which are irreversible, which can damage or destroy the cell.

For more info see Wikipedia: Lead-acid battery

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 15

What is an advantage of the low internal resistance of nickel-cadmium batteries?
  • Long life
  • Correct Answer
    High discharge current
  • High voltage
  • Rapid recharge

High discharge current is an advantage of the low internal resistance of nickel-cadmium (NiCd) batteries. This makes them great to use in portable electronic devices and tools which require high current flow.

For more info see Wikipedia: Nickle-cadmium (NiCd) batteries

High Discharge Rate Lithium Polymer Battery 5C

Last edited by jeff00seattle. Register to edit

Tags: arrl chapter 4 arrl module 15

What is the approximate junction threshold voltage of a germanium diode?
  • 0.1 volt
  • Correct Answer
    0.3 volts
  • 0.7 volts
  • 1.0 volts

\(0.3\) Volts is the approximate junction threshold voltage of a germanium diode.


This threshold is the voltage over which the diode can conduct significant current. Different materials have different junction threshold voltages, so the value for each diode is determined by the properties of the material(s) used in its construction.

For example, a diode made of silicon has a junction threshold voltage of about \(0.7\) Volts.


Silly Hint:

G for Germanium is about \(\frac{3}{10}\) (\(0.3\) V) of the way through the alphabet while S for Silicon is about \(\frac{7}{10}\) (\(0.7\) V) of the way through the alphabet.

For more info see Wikipedia: Diode

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 14

Which of the following is an advantage of an electrolytic capacitor?
  • Tight tolerance
  • Much less leakage than any other type
  • Correct Answer
    High capacitance for a given volume
  • Inexpensive RF capacitor

An advantage of electrolytic capacitors is that they have high capacitance for given volume.

These capacitors are often used in power supplies for AC voltage filtering.

They are polarized and must be placed in the circuit in the proper orientation, as reverse-voltages can cause catastrophic (explosive) failure. Bad electrolytic caps can swell and leak the electrolyte out the vent grooves notched in the top, appearing as a crusty substance. Also the electrolytic capacitors may have large variations in capacitance due to their method of manufacture.

For more info see: Electrolytic capacitors

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 12

What is the approximate junction threshold voltage of a conventional silicon diode?
  • 0.1 volt
  • 0.3 volts
  • Correct Answer
    0.7 volts
  • 1.0 volts

The approximate junction threshold voltage of a conventional silicon diode is \(0.7\) volts.


This threshold voltage is the voltage where the diode can start to conduct the greater part of the current. The material a diode is made from is a significant factor in what the threshold voltage will be. For example, the germanium diode has a junction threshold of about \(0.3\) volts.


Silly Hint:

S for Silicon, S for Seven. Also, the letter S is about \(\frac{7}{10}\) (0.7 volts) of the way through the alphabet. (As opposed to Germanium where G is about .3 the through)

Silicon has (7) letters***

For more info see Wikipedia: Diode

Last edited by thatshortgymchick772. Register to edit

Tags: arrl chapter 4 arrl module 14

Which of the following is a reason not to use wire-wound resistors in an RF circuit?
  • The resistor's tolerance value would not be adequate for such a circuit
  • Correct Answer
    The resistor's inductance could make circuit performance unpredictable
  • The resistor could overheat
  • The resistor's internal capacitance would detune the circuit

One reason not to use wire-wound resistors in an RF circuit is that the resistor's inductance could make the circuit performance unpredictable.

The construction of a wire wound resistor is VERY similar to that of an inductor. So in situations where extra inductance may be an issue (such as RF circuits), they are not a good component choice.

Silly Hint: Something that is Unpredictable is usually something you do NOT choose.

For more info see Wikipedia: Wire-wound resistors

Last edited by kf0gtr. Register to edit

Tags: arrl chapter 4 arrl module 13

What are the stable operating points for a bipolar transistor used as a switch in a logic circuit?
  • Correct Answer
    Its saturation and cutoff regions
  • Its active region (between the cutoff and saturation regions)
  • Its peak and valley current points
  • Its enhancement and depletion modes

The stable operation points for a bipolar transistor used as a switch in a logic circuit are its saturation and cut-off regions. The saturation region acts as a good "full on" switch position, whereas the cut-off region acts as a good "full off" switch position.

For more info see wikipedia: Bipolar junction transistor

HINT: Famous Painter Van Gogh was BIPOLAR. He used SATURATED colors and he CUT OFF his ear.

Last edited by missourib. Register to edit

Tags: arrl chapter 4 arrl module 14

What is an advantage of using a ferrite core toroidal inductor?
  • Large values of inductance may be obtained
  • The magnetic properties of the core may be optimized for a specific range of frequencies
  • Most of the magnetic field is contained in the core
  • Correct Answer
    All these choices are correct

This question could be asking about a couple of things:

(1) What advantage does a toroid core provide as opposed to a straight core?

(2) What advantage does a ferrite core provide as opposed to a powdered iron core?

Based on the correct answer, it seems like it's only asking about toroid versus straight.

Toroids have become popular because the amount of magnetic flux that leaks outside of the core itself is low, which makes it more efficient and it radiates less electromagnetic interference.

Additionally, toroid cores are a closed loop. In a straight core the magnetic field has to go pretty far from one end to enter at the other. This means that the toroid will typically produce a larger inductance.

Finally, by varying the size and thickness and characteristics of the ferrite itself, you can optimize a ferrite toroid for different frequencies.

Silly Hint: the TOROIDAL inductor gives you the TOTAL package.

For more info see Wikipedia: Toroidal inductor

Last edited by glitteribbon. Register to edit

Tags: arrl chapter 4 arrl module 12

Which of the following describes the construction of a MOSFET?
  • The gate is formed by a back-biased junction
  • Correct Answer
    The gate is separated from the channel with a thin insulating layer
  • The source is separated from the drain by a thin insulating layer
  • The source is formed by depositing metal on silicon

A MOSFET (Metal Oxide Semiconductor Field Effect Transistor) is constructed so that the gate is separated from the channel with a thin insulating layer. The metal oxide is used in a thin layer to keep the gate from being in direct contact with the channel. This way the principal current flow is between the drain and the source, but not through the gate.

For more info see Wikipedia: MOSFET

Silly hint: The correct answer has the key words "Gate" and "Channel."

This is kind of a "gotcha" question, so you can think "GATe"+"CHAnnel" for "GAT-CHA."

Last edited by wscody. Register to edit

Tags: arrl chapter 4 arrl module 14

Which element of a triode vacuum tube is used to regulate the flow of electrons between cathode and plate?
  • Correct Answer
    Control grid
  • Heater
  • Screen grid
  • Trigger electrode

The control grid is the element of a triode vacuum tube used to regulate the flow of electrons between cathode and plate.

For more info see Wikipedia: Control grid

Hint: to “regulate” is to “Control” or remember that a triode tube has a control grid.

Last edited by edponce@yahoo.com. Register to edit

Tags: arrl chapter 4 arrl module 14

What happens when an inductor is operated above its self-resonant frequency?
  • Its reactance increases
  • Harmonics are generated
  • Correct Answer
    It becomes capacitive
  • Catastrophic failure is likely

Inductors have what is called a “Parasitic element” to them. Almost any electrical component you can think of has parasitic elements. Even the leads of a resistor have a parasitic behavior to them. The parasitic element for inductors is capacitance.

An inductor has a low distributed capacitance between terminal electrodes or the turns of a wire-wound conductor, and its inductance with such distributed capacitance resonates at a certain frequency. This frequency is called the SRF Self-Resonant Frequency, and the inductor does not function as an inductor beyond the self-resonant frequency.

When selecting an inductor for high-frequency circuits and modules, it is not enough to simply consider the required inductance. You need to take into account that the self-resonant frequency must be sufficiently higher than the usage frequency.

Capacitors are created by having metal objects in close proximity to each other, usually with a di-electric component separating them. Inductors are just a large amount of metal wire wrapped around a base. The wires interact with each other, creating a usually negligible capacitive effect, but an effect at that. If the inductor is sitting on a ground plane, the coil will even have a capacitive effect between the wires and the ground plane it is sitting upon.

To combat this, manufacturers will make their inductors with an SRF one decade above the intended frequency range (10x the frequency).

Once the inductor hits the point of its SRF, the inductive component drops to basically zero. What’s left is essentially a capacitor.

Hint: Pushing an inductor too far makes it a capacitor (the opposite)


Parasitic Element

In electrical networks, a parasitic element is a circuit element (resistance, inductance, or capacitance) that is possessed by an electrical component but which it is not desirable for it to have for its intended purpose. For instance, a resistor is designed to possess resistance, but will also possess unwanted parasitic capacitance.

Last edited by jeff00seattle. Register to edit

Tags: arrl chapter 4 arrl module 13

What is the primary purpose of a screen grid in a vacuum tube?
  • Correct Answer
    To reduce grid-to-plate capacitance
  • To increase efficiency
  • To increase the control grid resistance
  • To decrease plate resistance

The screen grid insulates/isolates the control grid from the plate which helps counteract the Miller effect by reducing the grid-to-plate capacitance.

Hint: SCREEN it to reduce it.

For more info see Wikipedia: Vacuum tube

Last edited by nrunner. Register to edit

Tags: arrl chapter 4 arrl module 14

Why is the polarity of applied voltages important for polarized capacitors?
  • Incorrect polarity can cause the capacitor to short-circuit
  • Reverse voltages can destroy the dielectric layer of an electrolytic capacitor
  • The capacitor could overheat and explode
  • Correct Answer
    All these choices are correct

All of these choices are correct


Consider a common type of polarized capacitor: an electrolytic capacitor. Electrolytic capacitors must be connected in the way specified, since the dielectric, usually a thin film of metal oxide, rapidly breaks down when current in the wrong direction is applied.

When the dielectric breaks down, the two "plates" of the capacitor can short out, generating a large amount of current to go through the capacitor and causing massive heating. These rapid and violent changes can result in a venting of hot liquid, or sometimes in dangerous explosions.

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 12

Which of the following is an advantage of ceramic capacitors as compared to other types of capacitors?
  • Tight tolerance
  • High stability
  • High capacitance for given volume
  • Correct Answer
    Comparatively low cost

Ceramic capacitors have the advantage over other types of capacitors in they provide good function at comparatively low cost.

Silly hint: Ceramic Capacitors are Cheap

For more info see: ceramic capacitors

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 4 arrl module 12

Go to G5C Go to G6B